1remodel480320-1

How Do You Use A Wood Jointer

Tuning Seasonal or occasional tuning may be necessary. You may also have to do an initial tuning after your plane acclimates to the humidity level of your shop.

Do not use this jointer for other than its intended use. When working a piece of wood on the jointer, follow the 3-inch radius rule: capacity for this size jointer. Visit our website at . powermatic.com . to see a range of available dust collection units.

When you use the jointer, stand to the left of the machine (opposite the drive shaft) and you are cutting with the grain of wood; when this isn’t possible, make very light cuts, very slowly. Note: The depth of cut is exagger-ated for clarity.

If you have any questions relative to its application DO NOT use the product until you have written Delta Machinery Use wood dust collection FEED THE WOOD THROUGH THE JOINTER AT DIFFERENT SPOTS

___ WOOD ___ Woodcraft ___ WOODEN Boat ___ Woodshop News DO NOTuse the jointer as a toy. DO NOT use near or around children. 15. ENSURE that the machine sits firmly before using. If the machine wobbles or is unstable, correct the

Tool Name : 7" Rabbeting Jointer With Stand Item Number: 31849 Motor: 1 HP, 110V, 4.9 Amps, 750 Watts, Single Phase Use only wood boards. Do not force feed your work through the machine. Allow the Jointer to feed at the designated rate of feed.

Do not use this jointer for other than it intended use. If used for other purposes, WMH Tool Group Allow wood to dry or use different Fuzzy grain. stock. Dull knives. Sharpen or replace knives/inserts. Cutterhead slows while operating.

Turn on the power and allow the jointer to come to full speed. Listen for any odd noises, rubbings, vibrations, etc. If any are present, notify the Shop Leader.

When working a piece of wood on the jointer, follow the 3 inch radius rule. The hands must never be closer than 3 inches to the cutterhead. See Fig. 1. Do not use this jointer for other than it intended use. If used for other purposes, WMH Tool

Use wood dust collection systems whenever possible. 4 ADDITIONAL SAFETY RULES FOR JOINTERS 1. DO NOT OPERATE THIS MACHINE until it is Delta Model 37-380 is a 8" Professional Jointer with a cutting capacity of 8" (203mm) width, 1/8" depth (3mm max.) and

Jointer Knife Setup Jig Instructions CAUTION: Make sure the power supply is disconnected on your power tool(s) When choosing a straight edge, you may use a metal or wood piece of material. Wood is preferable to do this as some metal types may damage the knife.

Is very likely to catch, throwing the wood out of your hand and allowing the fingers to drop into the revolving cutterhead. Maintain you balance when operating the jointer; do not overreach or use excessive force to perform any operation. Establish a comfortable position prior to starting.

64 FINE WOODWORKING y beginning students often ask me, “Which machine should I buy first, a planer or a jointer?” The answer is both. That’s one reason why this Tools & Shopsissue

Be careful that you do not run any material that might have nails, screws, or loose knots over the jointer. It not only would damage the machine, You must not use the jointer for wood less than 12 inches long. The material must be long

2 This manual has been prepared for the owner and operators of a Powermatic Model 54A Woodworking Jointer. Its purpose, aside from machine operation, is to promote safety through the use of accepted

If you have any questions relative to its application DO NOT use the product until you have written Delta Machinery Use wood dust collection Delta ShopMaster Model JT360 is a Deluxe 6" (152mm) Jointer with designed cutting capacity of 6" (152mm) width,

___ WOOD ___ Woodcraft ___ WOODEN Boat ___ Woodshop News DO NOTuse the jointer as a toy. DO NOT use near or around children. 15. ENSURE that the machine sits firmly before using. If the machine wobbles or is unstable, correct the

Are sandwiched between wood blocks, see photo below. STONES. If you change jointer knives fre-quently, a Magna-Set will allow you to do it very quickly. The Magna-Set consists of two plastic bars that rest on the out-

Do you have a dial indicator I can use to set my jointer knives right? Iʼm having a hard time making sure theyʼre flush with my outfeed table to

Recommended Reads....


Please Share Us:
Votes 135

Rating: 5 out of 5

Updated: September 11, 2014 — 6:08 pm

Site Disclaimer: This site is designed for educational purposes only, if you click on a link and make a purchase I will make a small commission. Furthermore, all videos and photos on this site are provided by 3rd parties. We take no responsibility for the content on any website which we link to, please use your own discretion while surfing the links.

Frontier Theme

Enjoy this blog? Please spread the word :)